Tulip Artisan Tie-Dye Soda Ash Method Kit
Tulip Artisan Tie-Dye Soda Ash Method Kit

Tulip Artisan Tie-Dye Soda Ash Method Kit

Regular price Rs. 1,149.00 Rs. 0.00 Unit price per
GST included. Shipping calculated at checkout.


The Tulip® Artisan™ Tie-Dye System gives you the vibrant colour and control needed to create professional and artist-quality tie-dye results. Tulip Artisan Tie-Dye utilises the classic two-step soda ash method and features MaxVibrant Fibre Reactive Dyes™ that contain ultra concentrated, ultra vibrant dye pigments. The thicker, richer formula provides unsurpassed colour vibrancy and maximum dye control for sharper, more defined tie-dye patterns. Let your inner artist out to play with the unparalleled brilliance of the Tulip® Artisan™ Tie-Dye System.

This kit contains:

  • (3) 118ml pre-filled bottles of premium fibre-reactive dyes
  • Trial-size bottle of black dye
  • (1) bag of soda ash
  • (2) pairs of high-quality latex gloves
  • (20) rubber bands
  • Instruction guide

How to Use:

1. Protect work surface with plastic trash bags or a disposable plastic table cover. Cover with a layer of paper towels to absorb excess dye. Tip: You can also dye your project on a large pastry cooling rack set over your sink to prevent fabric from sitting in pooled dye.
2. Prewash fabric to remove sizing. Choose a natural fibre fabric to best absorb the dye into the fibres (cotton, wool, rayon, silk). Do not use fabric softener or dryer sheet. 
3. Mix soda ash solution in a large bucket according to package directions and soak garment to be dyed. Wring out excess solution before binding fabric.
4. If you are planning to dye your project dry, tie your garment into desired tie pattern and allow to dry. If you are dying your project wet, tie into desired tie and proceed with dyeing. Note: Mixed soda ash solution can be used multiple times until gone, and does not lose effectiveness over time.
5. Wearing gloves from kit, add water to dye bottle, filling to line. Replace cap tightly. Shake until dye is dissolved and allow mixed dye to set for time suggested in package instructions to achieve maximum dye consistency. Use full-strength for intense colours. For a lighter shade of colour, add more water using extra bottle if needed.
6. Apply dye on fabric, checking to make sure dye has penetrated into folds. Do not over-saturate fabric. If dye is applied too close together, the colours may become muddy.
7. Cover dyed fabric with plastic wrap to keep damp. Or leave project on pastry cooling rack and cover with plastic. Let set 6-8 hours or over night for most intense colours.
8. Fully rinse dyed fabric in warm water until all extra dye is removed and water runs clear - removing rubber bands if used. Fill washer to large load setting with hottest water suitable for the fabric and a small amount of laundry soap. Wash and dry separately. Wash separately the first few washes. Do not allow dyed fabric to rest wet on other items.


  • Note: Do not add water to dye until you are prepared to apply it.
  • Allow mixed dye to sit after mixing for time suggested in instructions to achieve maximum thickness. Thicker dye will result in less colour penetration and more border definition, whereas thinner dye will penetrate and blend more on fabric.
  • Apply dye within 24 hours after mixing. Dye left unapplied after 24 hours will begin to lose concentration and will result in noticeably weaker colour intensity.
  • Plastic wrap or a disposable plastic table cover can be used for larger work areas.
  • Dyeing your project on a pastry cooling rack placed over the sink helps minimize drips and helps keep colours from merging on the bottom of project.
  • Place small items in laundry bag for washing. If darker dye drops on lighter dye, rub off to remove excess. Make sure excess dye dust is removed from work area. It is invisible until it reacts with water.
  • Create new colours by blending dye colours. Create lighter colours by adding more water to mixed dye.
  • Test mixed colours on scrap fabric, adding more dye or water to achieve desired colour or intensity.
  • Cover dyed fabric with plastic to keep it from drying out. Projects can be left on cooling rack and covered to keep dye colours separate.
  • Precautionary note: Always wear gloves when working with dyes. Dry dye powder can cause an allergic reaction in some people. Avoid inhaling dye dust over an extended period of time. Use in well-ventilated area. Supervise children doing tie-dye projects.
  • Caution: May irritate skin and eyes. Avoid contact with eyes, skin or clothing. Do not swallow. Wear rubber gloves and safety glasses. Keep out of reach of children.
  • First Aid Treatment: Contains organic dye and sodium bicarbonate. If swallowed, contact a poison control centre or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, rinse well with water. Adult supervision required.